Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Concord: What to Know First

We provide independent Ghost Controls gate parts and welding service in Concord, typically completing hinge replacements, post repairs, and rail welding within one scheduled visit after our free on-site estimate. Most Ghost Controls swing-gate and slide-gate hardware issues in Concord run $180-$650 depending on whether we’re resetting a twisted rail or fabricating a new hinge bracket from scratch. We write the price before we pick up a tool, and we leave a photo record of every weld and every part installed.

Call (510) 726-7050

This page is for Concord homeowners who already know they own a Ghost Controls system and need the mechanical side fixed, not the motor replaced. If your gate is sagging, dragging, or the latch won’t catch, call us at (510) 726-7050 for a free estimate with a written price.

How Ghost Controls Products Fail - and How We Fix Them

• TDS2 and TSS1 series hinge fatigue on inward-swinging driveway gates. These lighter-duty Ghost Controls operators are often paired with ornamental iron gates that weigh more than the hinge spec assumes. In Concord, we see this most on homes near Todos Santos Plaza where 1980s-era gates got retrofitted with newer operators. The top hinge pin elongates the bracket hole until the gate drops 3/8 inch and the actuator arm starts binding. We remove the bracket, weld a reinforced gusset plate, and ream the hole to true. If the post itself is rotted or cracked, we replace it with pressure-treated 4×4 or steel post depending on the gate weight.
• ABF and DTP1 battery box mounts tearing off welded angle-iron frames. Ghost Controls battery boxes hang from a small welded tab that takes vibration stress every cycle. After 800-1,200 cycles in Concord’s dry summer heat, the weld cracks propagate through thin-wall tubing. We don’t just re-weld the tab. We cut back to sound metal, add a spreader plate to distribute load, and weld with ER70S-6 wire on a clean joint so the repair outlasts the original.
• Slide gate rollers on GC and GHOST series track systems seizing in the housing. The sealed bearing rollers Ghost Controls specifies are adequate for clean environments, but Concord’s valley dust and occasional oak pollen buildup grind the seals. The roller housing then welds itself to the axle through corrosion. We cut the old roller free, clean the axle to bare steel, and install a heavier-duty sealed roller with zerk fitting so future maintenance doesn’t require a torch.
• Gate rail separation on welded tubular frames after ground shift. Concord sits on a mix of clay and alluvial soils that expand and contract seasonally. We’ve repaired dozens of Ghost Controls gates in the Dana Estates and Holbrook Heights areas where rail-to-stile welds cracked after winter rains. We V-out the crack, weld with proper penetration, and add an internal sleeve on gates over 12 feet wide so the repair doesn’t telegraph through the paint six months later.
• Latch misalignment on Ghost Controls single-swing gates with settling posts. The magnetic or mechanical latch Ghost Controls includes has only 1/2 inch of adjustment. When the gate post tilts even slightly, the striker misses entirely. We diagnose whether the post is moving in its footing or the hinge side has dropped, then either re-plumb the post with concrete or weld an adjustable striker bracket that gives you back 2 inches of tolerance.

Our Ghost Controls Gate Parts & Welding Process

1. 1
   Call and schedule. A live person answers at (510) 726-7050 24 hours a day. We book a free on-site estimate, not a “we’ll show up and see” visit.
2. 2
   On-site diagnosis with documentation. We photograph the failure point, measure gate weight and post embedment depth, and test the operator’s force settings so we don’t fix the metal only to have the motor tear it apart again.
3. 3
   Parts decision: OEM vs. quality aftermarket. Ghost Controls OEM hinges and brackets fit precisely but ship from Texas with 3-5 day lead times. For urgent repairs, we stock Concord-compatible heavy-duty equivalents that match or exceed the gauge and finish. We explain the trade-off and the price difference before you decide.
4. 4
   Written price, then work. Under Haven Standard Clause 1, you get a flat written price before any welding starts. No time-and-materials surprises.
5. 5
   Repair, test, and record. We weld, grind, prime, and test-cycle the gate under load. Before we leave, you get a photo log of every weld bead, every part number, and every adjustment.
6. 6
   365-Day Done Right Promise. If the weld cracks, the hinge loosens, or the roller seizes within one year, we make it right at no charge. No expiration games.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Concord

These are real Concord prices for real jobs we’ve completed, not national averages. The only way to get your exact number is a free on-site estimate. We write the price before we start, and that’s the price on the invoice. Call (510) 726-7050 to schedule.

Why Concord Homeowners Call Vance Gate Repair Concord for Ghost Controls Work

We’ve repaired and installed over 22,000 gates since 2014, and a growing share of our Concord calls are Ghost Controls systems that the original installer no longer services. We don’t steer you toward a motor replacement when the problem is a $200 hinge weld. We also don’t pretend Ghost Controls is the only brand we know. Our technicians carry parts and documentation for LiftMaster, Mighty Mule, and DoorKing systems too, so if your gate needs a mixed-brand solution, we can build it.

Every visit follows The Haven Standard: written price before work, photographed record after, and the 365-Day Done Right Promise backing it all. Our technicians are background-checked, uniformed, and named before they arrive. Adrian Vance started this practice in commercial access-control work and brought it to every residential driveway gate we touch. Name what you found. Name what it costs. Name what you left behind.

FAQs